SIM808 Arduino - Raspberry Pi GSM - GPS - GPRS Development Module (IMEI No Registered)

Arduino - Raspberry PI GSM - GPS - GPRS Development Module (IMEI No Registered)

ItGSM - GPS - GPRS Development ModulenudeArduino and Raspberry PiYou can use it with.

Turkey Located in the legal registration IMEI simple phone with this module, the SMS function of the applications, vehicle tracking, all that may come to your mind and M2M applications GSM / GPS / GPRS can improve operations. Feeding can be made from 3 separate entrances on it:

1. With 5-26V from DC044 input,
2. With 3.7-4.2V Lipo / Lion battery,
3. It can be supplied with 5-26V from the Vin input.

Make sure that the supply to be made has a 2A power. Module SIM808 is programmed using AT commands.

The power button turns the module's power on and off. Power Led turns on when the Power is turned ON. In addition, to start the module, it is activated by pressing the button on the side of the module for 2 seconds. The SIM slot is located under the Module.

If the GSM, GPS antennas and SIM card are installed properly, the LED will blink every 3 seconds. This is an indication that the Module is connected to the network. So you can make a call or make other operations.

The module, which also includes a vibration motor, works with 5V and is controlled by the pin located in the upper right corner of the module. SIM808, which has Bluetooth on it, is controlled by AT commands.

Communication is done with the SIM8080 module Arduino and Raspberry pi using Rx-Tx and GND pins. The issue to be considered here; If your processor system uses 1.25V / 3.3V / 5V, you must connect the VMCU pin to the 1.25V / 3.3V or 5V supply of this system. Because the level converter on the SIM808 module enables the VMCU and Rx / Tx pins to work at this level. The USB socket is used only for firmware update.

Note:In this moduleGSM and GPSRequired antennas forincluded,Bluetoothantennanot included.

Arduino ve Raspberry Pi GSM - GPS - GPRS Development Module Features

• Maximum current: 2A
• Sleep mode Current:<2mA
• Dimensions: 79.5mm X 50mm X 15mm
• Weight: 70g
• Frequency Band: Quad-Band 850/900/1800 / 1900MHz
• GPRS Connection class: 2G GPRS multi-slot class 12/10
• GSM transmitter Power: Class 4 (2 W @ 850/900 MHz), Class 1 (1 W @ 1800 / 1900MHz)
• GPRS Uplink / Downlink speed: Max 85.6Kbps
• MUX Protocol: 0710
• Connection protocol: PPP stack, USSD
• Transfer protocol: Embedded TCP / IP-UDP

SMS over GSM / GPRS:

• Point to Point MO and MT
• SMS cell broadcast
• Text (ASCII) and PDU

Supported software features:

• FTP / HTTP
• MMS
• POP3 / SMTP
• DTMF
• Jamming Detection
• Audio Recording
• SSL
• Bluetooth
• Control with AT commands -
• Standard AT Commands: GSM 07.07 & 07.05
• Extended AT Commands: SIMCOM AT Commands

GPS Features:

• Receiver type: 66 satellite records and 22 satellite tracking, GPS channel L1 C / A codes
• Sensitivity: Satellite tracking -165dBm, (cold) -148dBm at startup
• First fix time:
  • Cold Start 32 seconds (typical),
  • Hot Start<1san
  • Half warm start: 3sec
• Horizontal position accuracy:<2.5m CEP

Hardware Features:

• Serial (RS232 1.25 / 3.3 / 5V, TTL Level)
• SPI
• RTC (Clock Battery backed)
• Analog audio input / outputs

Certifications:

• CE, A-TICK, TA, CCC

Scope of application:

• Vehicle Tracking systems
• Security systems
• M2M (Machine 2 Machine) / Scada Applications
• Remote data and device control applications
• Sending SMS
• Receiving SMS
• Phone Applications (Voice exchange)
• Sending camera apps (periodic Photos).

Documents

• Sim808 GSM GPS DatasheetCheck the file.
• Sim808 GPS Application NotesCheck the file.
• Sim900 User GuideCheck the file.